NORDGROUTH TIXOEXPANSIVE, THIXOTROPIC, FIBRE-REINFORCED MORTAR

Pre-mixed mortar to be prepared with the addition of water alone. It is suitable for repair and structural reinforcement jobs, with or without the aid of a steel mesh. Highly recommended for creating structural overlays in counterthrust waterproofing jobs.

MALTAFIXULTRA-FAST ZERO-SHRINKAGE THIXOTROPIC MORTAR

A pre-mixed mortar available in plastic bags for repair work on concrete floors, beams and pillars, asphalt sheets and all applications in which the repaired section must be put back into service quickly.

NORPHEN FONDO IGROSOLVENT-BASED MONO-COMPONENT PRIMER

Solvent-based mono-component primer for treating sanded or smoothed CONCRETE surfaces to eliminate dust before the application of BETONSEAL MS 2.0 and before laying EASY LAST 90 in case of particularly dusty surfaces.

BETONSEAL MS 2.0WATERPROOFING ADHESIVE SEALANT

A mono-component sealant suitable for the watertight sealing of all
elastic bridges and for creating watertight fillets between screeds and
walls, sub-thresholds, drains and pass-through pipes before the application of waterproof membranes. For sealing of pipes, grilles and flanges in swimming pools, hydromassage tubs, Turkish baths, bathrooms, etc. It can be covered just one hour after its application, to obtain excellent adhesion with any coating or waterproofing material.

SW SOLIDBI-COMPONENT WATER-BASED CONSOLIDATING AGENT

A bi-component epoxy cortical consolidation product in water emulsion for treating chalking screeds, concrete, mortar and stone.

FONDO SLBI-COMPONENT SOLVENT-BASED CONSOLIDATING AGENT

A bi-component epoxy deep consolidating agent, prepared by adding 80% by volume of NORPHEN SOLVENTE to the A+B mixture: used to increase the compressive strength of chalking screeds, mortar and stone.

GROVE PRIMER ECO
ADHESION AND MIX-ALTERING PRIMER

A water-based liquid adhesive that, when blended with a screed mix, changes into a structural binder for the adhesion of GROVE MASSETTO and for ready-made screeds of the SC series.
It binds to any surface (old screeds, concrete, tiles, wood, etc.)

GROVE MASSETTO
FINE-GRAIN SCREED FOR MODIFYING SLOPES

Used together with GROVE PRIMER, it is a powdered pre-mixed product for adjusting sloping surfaces, for thin recasts or precise skim coating of screed or tiled floors of any type.

LEVEL FINO / LEVEL HB
SELF-LEVELLING FINE-GRAINED HIGH-BUILD MORTAR

A pre-mixed product prepared with the sole addition of water.
It creates a cement layer 3 to 10 mm thick (LEVEL FINO) or 6 to 30 mm thick (LEVEL HB). Ideally applied before the tiling of screeds.

SC1READY-MADE SAND AND CEMENT SCREED WITH CONTROLLED SHRINKAGE

A cement-based pre-mixed product for preparing substrates, featuring excellent mechanical properties. Heat-conductive, with controlled shrinkage and medium to fast setting (4–8 days).

SC1FREADY-MADE SAND AND CEMENT SCREED WITH CONTROLLED SHRINKAGE, ADMIXED WITH SEMI-STRUCTURAL FIBRES

A cement-based pre-mixed product with controlled shrinkage, medium-fast setting (4–8 days) for screeds with characteristics superior to SC1. Particularly suitable for creating radiant screeds, thanks to its high thermal conductivity.

SC1 BASEBINDER FOR MEDIUM- TO FAST-SETTING SAND AND CEMENT SCREEDS

A binder specially formulated for preparing substrates with high mechanical characteristics, with controlled shrinkage and medium- to fast-setting, with the sole addition of screed aggregates.

FAST FLUID 300ADDITIVE FOR SCREEDS, DRYING ACCELERATOR

It is a liquid to be added to sand and cement screed mixtures for accelerating drying and setting: in ideal conditions, the screed is ready for laying with cement adhesive just 24 hours after casting.
Used at 1.5% by weight of the cement.

FAST FLUID AGADDITIVE FOR SCREEEDS, FROSTPROOFER

A liquid to be added to sand and cement screed mixtures for protection against frost and as a setting accelerator. Chloride-free.
Used from 1% to 2% by weight of the cement depending on the work temperature. When added to the mixture together with FAST FLUID 300, it speeds up setting even at very low temperatures.

NORDECAL FORTE GELHIGHLY ACIDIC DETERGENT

Acid descaling gel detergent for acid washes on concrete, terracotta, Tuscan cotto, facing bricks and stone used on vertical and horizontal surfaces.

STRIPPERNEUTRAL DETERGENT

Neutral detergent with a powerful detergent action for removing grease, dirt and tyre marks caused by vehicles.

PLAST EPOFILLER FOR REPAIRING CRACKS WITH STEEL BARS

A lightweight bi-component filler for filling and rigidly sealing any building surface. It is highly recommended for anchoring steel bars when repairing structural and mobile cracks on sand and cement screeds, and on concrete walls and floors (swimming pools and water tanks in particular). Also suitable for eliminating expansion joints in concrete floor slabs before applying rigid resin treatments.

NORPHEN RICRETEBI-COMPONENT EPOXY PRIMER

Viscous fluid epoxy binder for structural bindings of concrete on concrete. Also effective in highly damp conditions.
Also suitable for binding plasters, screeds and recasts consisting of pre-mixed sand and cement mortars for structural interventions.

MALTA BASEBI-COMPONENT EPOXY BINDER

A solvent-free bi-component epoxy binder that, with the addition of quartz sands featuring special grain-size curves, creates mortars that can be used for forming slopes and for filling depressions when preparing substrates before the application of resins.

W3 IMPERMEABILIZZANTETHREE-COMPONENT EPOXY SKIM COAT – 03 GRAIN SIZE – SR_B 2.0

Skim coat for old and new concrete surfaces with high mechanical strength and high tear resistance, ideal for skim coating of surfaces subject to rising damp. It can be admixed with quartz sands and used as a coating for outdoor floors or to prevent bubbles from forming prior to the application of elastomeric coatings for sports facilities. Recommended, with the addition of quartz sand, also for cortical repairs on outdoor industrial floors.

GROVE RIPRISTINOTHIXOTROPIC FIBRE-REINFORCED MORTAR FOR RECONSTRUCTING CONCRETE

A powdered pre-mixed product to be prepared by adding water for obtaining a normal-setting mortar, even to a high thickness (up to 5 cm) with a single coat.

GROVE RAPIDOFAST-SETTING THIXOTROPIC FIBRE-REINFORCED MORTAR

A powdered pre-mixed product to be prepared by adding water for obtaining a fast-setting mortar, to a thickness of up to 6 cm with a single coat.

MALTAFIXULTRA-FAST ZERO-SHRINKAGE THIXOTROPIC MORTAR

A pre-mixed mortar available in plastic bags for repair work on concrete floors, beams and pillars, asphalt sheets and all applications in which the repaired section must be put back into service quickly.

NORDGROUTH TIXOEXPANSIVE, THIXOTROPIC, FIBRE-REINFORCED MORTAR

Pre-mixed mortar to be prepared with the addition of water alone.
It is suitable for repair and structural reinforcement jobs, with or without the aid of a steel mesh.
Highly recommended for creating structural overlays in counterthrust waterproofing jobs.

GROVE 30RECASTING MORTAR FOR LARGE SURFACES WITH THICKNESS FROM 1 TO 30 mm, DIRECT FINISH

A powdered pre-mixed product prepared by adding water for obtaining a thixotropic mortar that is also ideal for low thicknesses.
It is mainly used for overlays on incorrectly finished concrete surfaces, such as walls of tubs, tanks, swimming pools and items in general that need to be rectified. It can be finished directly with a trowel without any need for final skim coating applications.

NORPHEN INJECTIONBI-COMPONENT CONSOLIDATING AGENT FOR INJECTIONS

Bi-component zero-shrinkage epoxy consolidating agent for low-pressure injection into structures requiring consolidation by means of binding and filling.

GROVE RASANTECEMENT-BASED MONO-COMPONENT SKIM COAT – GRAIN SIZE 06 – R2

A skim coat formulated for freshly cast concrete surfaces. Inexpensive and quick to apply. For skim coats up to 5 mm thick.

RASANTE 2000 2KBI-COMPONENT FINE-GRAINED SKIM COAT – GRAIN SIZE 03

A skim coat for masonry consisting of a liquid part (resin) and a powdered part.
It is ideal for obtaining perfectly smooth, flexible finishes with excellent adhesion on any surface. Excellent for subsequent treatments with decorative resins.

RASANTE 1100LIME-BASED MONO-COMPONENT SKIM COAT WITH HIGH BREATHABILITY GRAIN SIZE 06

A skim coat for masonry, formulated for new surfaces (or old surfaces, when used with a primer) for two-coat rendering, to be used with the “wet on wet” technique, also for dehumidifying plasters.

RASOMIXMONO-COMPONENT POWDERED CEMENT-BASED PLASTER-SKIM COAT GRAIN SIZE 06

A special, zero-shrinkage, shapeable product that allows for making thin and very thick skim coating applications with a single coat. Particularly recommended for painting teams due to its extensive flexibility of use (also as a substitute for plaster) and for the savings on workmanship.

RASANTE 1200CEMENT-BASED MONO-COMPONENT SKIM COAT – GRAIN SIZE 06

Skim coat with high resin content, suitable for skim coating any type of new or old surface, over plaster, plastic coatings or cement.

RASANTE 1200 SCEMENT-BASED MONO-COMPONENT SKIM COAT – GRAIN SIZE 1.15

Like RASANTE 1200 but with larger grain size and superior mechanical performances.

W3 IMPERMEABILIZZANTETHREE-COMPONENT EPOXY SKIM COAT – 03 GRAIN SIZE – SR_B 2.0

Skim coat for old and new concrete surfaces with high mechanical strength and high tear resistance, ideal for skim coating of surfaces subject to rising damp. It can be admixed with quartz sands and used as a coating for outdoor floors or to prevent bubbles from forming prior to the application of elastomeric coatings for sports facilities. Recommended, with the addition of quartz sand, also for cortical repairs on outdoor industrial floors.